Bezel for 1.5 inch 128×128 SH1107 OLED display. Standard size

£8.00 – £16.00

This bezel makes your Arduino, Raspberry PI or other project look neater and more professional.

This bezel has been specifically made to fit the 1.5″ SH1107 128×128 OLED Display Module shown in this listing’s images. The display’s PCB is 47mm x 34mm.

See the gallery images to see the specific OLED. This bezel is unlikely to fit any other OLED display with a different layout. Please carefully check the dimensions of your display before buying.

This product comes in two options:
1) A bezel only, to fit a 1.5″ OLED display as specified.
2) A bezel supplied with a matched and tested display as specified.

 

SKU: BEOL15S Categories: , , ,

Description

It is difficult to mount the 1.5″ OLED display in an enclosure without making an untidy hole and using ugly fixing screws. This bezel makes your project look more professional and tidy, and does away with ugly display mounting screws.

The bezel will fit both the (4-pin) IIC and (7-pin) SPI variants of the display.

A High Quality Acrylic Part

This is a HIGH QUALITY part with a flat, very smooth, high-quality glossy surface, made from hard acrylic. This is NOT a low-quality 3D printed part (3D printed parts are typically made of soft, low-melting point plastic and have a rough, poor quality finish. Some 3D printer materials also do not accept adhesive making them difficult to use, and some material degrade).
Our acrylic bezels will make your project look more-professional and give a quality touch to projects, are easy to use, and readily accept many common adhesives.

Description

The front of the bezel has a nice high-gloss black finish, and all other sides and edges have a machined finish. This is not a moulded part.
The bezel has been designed so that the display window is centred both vertically and horizontally, for that ‘pro’ look.
The bezel is intended for landscape, but of course you may use it in portrait orientation. The visual display data should be rotated in software.
The outside corners of the bezel are rounded for a softer look.
 
The 1.5″ OLED display (which is OPTIONALLY included in this item), is attached to the rear of the bezel with adhesive. The bezel (with the display) is then fixed into your panel or enclosure and again fixed with adhesive.
NO adhesive is included with this bezel. 
Full instructions are included with this item.
 
This bezel has been specifically made to fit the 1.5” 128×64 SH1107 OLED display as show in the listings images – having a PCB size of 47mm x 34mm.
If you are unsure if your display will fit the bezel, please contact us before buying (or buy our combined bezel with matched and tested display).
 
Note that the bezel is not certified as moisture or dust proof.

Bezel Specifications

  • Overall bezel size: 58.74mm x 40mm.
  • Panel overlap: 3mm all round.
  • Panel cut-out: 52.74mm x 34mm.
  • Bezel Material: Perspex/acrylic
  • Colour: The front of the bezel is gloss black. The sides and rear of the bezel have a machined finish.
 *** This is a custom-machined item, so its measurements may vary slightly. All dimensions are nominal.

Display Specifications

  • Display module size: The bezel will accept the specified 1.5″ 128×128 OLED displays whose PCB measures 47mm x 34mm, and has identical layout to the display shown in in this listing.
  • Active display area: 28.86mm x  28.86mm (smaller than the glass)
  • Mount hole spacing: 42mm x 29mm (2.2mm holes)
  • OLED interface: 4-pin IIC (I2C)
 
The 1.5″ OLED module is OPTIONAL in this listing. Please make sure that, if you are using your own OLED, it has the correct dimensions, layout and design to fit the bezel.
Adhesives are NOT included.

Related products